AMBER Archive (2009)

Subject: RE: [AMBER] PDMED

From: Catein Catherine (askamber23_at_hotmail.com)
Date: Tue Jun 09 2009 - 01:18:59 CDT


Dear Ross,

 

Thank you. Installation in our supercomputer is nice. Could you mind to let me know how can we use pmemd? Are there any step by step instruction on how to run a pmemd calculations? Can we use the same prmtop, inpcrd and in files for pmemd? Should we call up the calculation with $AMBERHOME/pmemd ..... command rather than $AMBERHOME/sander ..... commands?

 

Thus, it also suport calculations with TIP3P. Good to give it a try.

 

Best regards,

 

Cat
 
> From: ross_at_rosswalker.co.uk
> To: amber_at_ambermd.org
> Subject: RE: [AMBER] PDMED
> Date: Mon, 8 Jun 2009 22:19:36 -0700
>
> Hi Catein,
>
> > I am trying to do the PDMED for the dynamics simulations. After
> > standard amber10 installation, I found pmemd and pmemd.amba directories
> > with src subdirectory for each of them.
>
> Note, it is 'PMEMD'. If you do not plan to run Amoeba calculations, or do
> not know what Amoeba is then you do not need to worry about pmemd.amba.
>
> $AMBERHOME/src/pmemd you may wish to build if you plan to run a lot of
> parallel jobs and/or large MD runs. PMEMD will be faster than Sander even at
> relatively low cpu counts. This has to be built separately from sander.
> Essentially:
>
> cd $AMBERHOME/src/pmemd/
> ./configure
>
> This will bring up a list of options for architectures etc. Take your pick
> and away you go...
>
> > Do I still need to install the PDMED according to the README file too?
>
> If you want to take advantage of its high speed and scaling yes.
>
> > I would like to do the 10 ns simulation for a protein-DNA-Drug complex
> > with explicit solvent TIP3 solvent box. Is it compatible with PDMED?
>
> Yes. PMEMD supports explicit solvent MD (including extra points for TIP4PEW
> etc) as well as implicit solvent GB simulations. It does not support
> multisander implementations, such as replica exchange, TI etc and it also
> does not support QMMM. See the PMEMD section of the AMBER manual for a full
> discussion.
>
> Other than that PMEMD will read standard sander input and will write sander
> output.
>
> > What can we do next to run the calculations? What is the step need to
> > be done so as to use PDMED in supercomputer system?
>
> Do you have a supercomputer? Or access to one? If so then you need to build
> (or buy someone a pint so they build it for you) PMEMD on said supercomputer
> linking to the correct MPI libraries etc for the machines interconnect. You
> can then run PMEMD on said supercomputer using scripts appropriate for the
> queuing system in use. For some up to date benchmarks see:
> http://ambermd.org/amber10.bench1.html
>
> All the best
> Ross
>
> /\
> \/
> |\oss Walker
>
> | Assistant Research Professor |
> | San Diego Supercomputer Center |
> | Tel: +1 858 822 0854 | EMail:- ross_at_rosswalker.co.uk |
> | http://www.rosswalker.co.uk | PGP Key available on request |
>
> Note: Electronic Mail is not secure, has no guarantee of delivery, may not
> be read every day, and should not be used for urgent or sensitive issues.
>
>
>
>
>
> _______________________________________________
> AMBER mailing list
> AMBER_at_ambermd.org
> http://lists.ambermd.org/mailman/listinfo/amber

_________________________________________________________________
More than messages–check out the rest of the Windows Live™.
http://www.microsoft.com/windows/windowslive/_______________________________________________
AMBER mailing list
AMBER_at_ambermd.org
http://lists.ambermd.org/mailman/listinfo/amber